Evaluation Module - Ethernet eHouse expression where is duke @ Home Smart Home Automation eHouse.Pro where is duke
Home_Automation eHouse is advanced solution for electronic house, to be applied to many algorithms, which operate independently of each other. Conduct testing and debugging much easier regulator on the table or installed in the building. Should Exhibition / Evaluation Module therefore, the first tool that allows you to design and test the installation and configuration of home automation, yet at the stage of design automation control. Smart interpretation module allows you eHouse4Ethernet home to test controllers at the table without where is duke the need for more time - consuming where is duke installation at home. Application Assessment module allows you to cancel where is duke the myths and assumptions about the real controllers in the system close to the target environment. Evaluation Module allows testing of all Ethernet controllers: CommManager LevelManager EthernetRoomManager next big EthernetHeatManager - Ethernet scale - based controllers on the PCB CommManager / LevelManager other through Ethernet controllers based on the PCB EthernetRoomManager allows direct connection of each input and output signals of the module : connected display for output status LEDs lighting sensors attached output - for visible light phototransistor temperature - LM335, MCP9700, MCP9701 switches connected to the digital inputs connected to lights display dimmer level control IR receiver EthernetRoomManager IR Emitter external audio control - Video Systems In addition, the unit's display connectors for automatic testing of all Ethernet where is duke controllers, resource performance and hardware: the digital input digital output measuring input - Analog / Digital converters PWM dimmers IR transmitter IR receiver in doubt whether the controller okay, a self - test software module testing for any damage. In one part of the evaluation of the module, allows to determine if any problems caused by damage to the automatic where is duke control module configuration error or system failure seriously damage the switch, sensor, Dimmer, actuator Interpretation and evaluation of the output of the module: Display module is tested various departments control algorithms, functionality and configuration: Section 2 output where is duke "Output" allows simultaneous testing of two medium - sized or one large controllers "ADC" - sensors to evaluate all input analog where is duke converter / digital "inputs "- digital input" IR transmitter "- IR transmitter" IR Receiver "- IR receiver" Dimmers "- PWM dimming normal and reverse" TEST "- own controller - Digital input test section Section - OUTPUT It has installed lights attached where is duke Each digital output of the regulator. Activation of the output will illuminate LED controller connected to a specific output. Niamh sections 42 and 40 respectively output allow testing of all types of Ethernet controllers. Digital Inputs Division - INPUT
It switches installed "push button" connected to each input (maximum 12), shorting them grounded when the button is pressed. Input connectors are compatible with standard ERM. Dimmers Division - Dimmers
Each controller has 3 DC PWM dimmers without power driver. Can output directly control the LED driver power transmission insulator in two ways: Normal - Led dimmer placed between where is duke the output (anode) and the system ground (cathode) Inverted (INV) - placed between the output of the dimmer LED (cathode) and the positive 3V3 voltage regulator (anode) In light dimmer uses lighting where is duke level. IR transmitter and receiver sections - IR infrared receiver section where is duke includes a receiver infrared signal IC for the self - test or quality control ERM Sony infrared remote control IR transmitter section includes infrared emitters (light emission in the infrared) with limiting resistors existing current to a safe value for the controller and lights. It is used to test the transmission of control signals for audio - video equipment from the ERM Division controller Analog Converter / Digital - ADC
The article is a series of sensors that can transfer analog inputs for sensors: up to 15 MCP9700 or MCP9700 sensor up to 14 sensors LM335 resistors to provide necessary voltage (3V3) of controller (Pull Up) sensor light - it is also phototransistor series of "jumpers & #
Home_Automation eHouse is advanced solution for electronic house, to be applied to many algorithms, which operate independently of each other. Conduct testing and debugging much easier regulator on the table or installed in the building. Should Exhibition / Evaluation Module therefore, the first tool that allows you to design and test the installation and configuration of home automation, yet at the stage of design automation control. Smart interpretation module allows you eHouse4Ethernet home to test controllers at the table without where is duke the need for more time - consuming where is duke installation at home. Application Assessment module allows you to cancel where is duke the myths and assumptions about the real controllers in the system close to the target environment. Evaluation Module allows testing of all Ethernet controllers: CommManager LevelManager EthernetRoomManager next big EthernetHeatManager - Ethernet scale - based controllers on the PCB CommManager / LevelManager other through Ethernet controllers based on the PCB EthernetRoomManager allows direct connection of each input and output signals of the module : connected display for output status LEDs lighting sensors attached output - for visible light phototransistor temperature - LM335, MCP9700, MCP9701 switches connected to the digital inputs connected to lights display dimmer level control IR receiver EthernetRoomManager IR Emitter external audio control - Video Systems In addition, the unit's display connectors for automatic testing of all Ethernet where is duke controllers, resource performance and hardware: the digital input digital output measuring input - Analog / Digital converters PWM dimmers IR transmitter IR receiver in doubt whether the controller okay, a self - test software module testing for any damage. In one part of the evaluation of the module, allows to determine if any problems caused by damage to the automatic where is duke control module configuration error or system failure seriously damage the switch, sensor, Dimmer, actuator Interpretation and evaluation of the output of the module: Display module is tested various departments control algorithms, functionality and configuration: Section 2 output where is duke "Output" allows simultaneous testing of two medium - sized or one large controllers "ADC" - sensors to evaluate all input analog where is duke converter / digital "inputs "- digital input" IR transmitter "- IR transmitter" IR Receiver "- IR receiver" Dimmers "- PWM dimming normal and reverse" TEST "- own controller - Digital input test section Section - OUTPUT It has installed lights attached where is duke Each digital output of the regulator. Activation of the output will illuminate LED controller connected to a specific output. Niamh sections 42 and 40 respectively output allow testing of all types of Ethernet controllers. Digital Inputs Division - INPUT
It switches installed "push button" connected to each input (maximum 12), shorting them grounded when the button is pressed. Input connectors are compatible with standard ERM. Dimmers Division - Dimmers
Each controller has 3 DC PWM dimmers without power driver. Can output directly control the LED driver power transmission insulator in two ways: Normal - Led dimmer placed between where is duke the output (anode) and the system ground (cathode) Inverted (INV) - placed between the output of the dimmer LED (cathode) and the positive 3V3 voltage regulator (anode) In light dimmer uses lighting where is duke level. IR transmitter and receiver sections - IR infrared receiver section where is duke includes a receiver infrared signal IC for the self - test or quality control ERM Sony infrared remote control IR transmitter section includes infrared emitters (light emission in the infrared) with limiting resistors existing current to a safe value for the controller and lights. It is used to test the transmission of control signals for audio - video equipment from the ERM Division controller Analog Converter / Digital - ADC
The article is a series of sensors that can transfer analog inputs for sensors: up to 15 MCP9700 or MCP9700 sensor up to 14 sensors LM335 resistors to provide necessary voltage (3V3) of controller (Pull Up) sensor light - it is also phototransistor series of "jumpers & #
No comments:
Post a Comment